Anodic behavior of nickel-based alloys in the electrolytic production of NF3

The Ni-based alloys, such as Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si, prepared by hot isostatic pressing (HIP) at 1000 °C under 2 × 10⁸ Pa for 2 h were employed as the anodes for electrolytic production of NF₃. The current efficiencies for NF₃ formation were 42-38, 52-40, 52-47, 63-62, 50 and 41% for Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloys, respectively. The current efficiencies only on Ni-Cu alloys with Cu concentrations lower than 10 mol% were almost the same as those on Ni sheet and HIPed Ni anodes, whereas those on the other alloys used in this study were smaller compared with those on both Ni anodes. On the other hand, the current losses caused by anodic dissolution of Ni-Co, Ni-Mn, Ni-Ag, Ni-Cu, Ni-Al and Ni-Si alloy electrodes were 7.95-4.42, 6.40-7.02, 5.60-6.30, 3.34-6.33, 5.10 and 0.18%, respectively. The anode consumptions of Ni-5 mol% Cu and Ni-5 mol% Si alloys were almost the same or smaller compared with those of Ni sheet and HIPed Ni electrodes, though those of other alloys used were large compared with those of both Ni anodes. Consequently, addition of Cu to the nickel matrix is available for a cheaper cost of anode with keeping a same current efficiency as that on the Ni anode and addition of Si to the nickel matrix is effective for decreasing anode consumption largely. A Ni sheet electrode containing a trace of impurities, such as Co, Mn, Ag and Al, is also favorable as the anode for electrolytic production of NF₃.     

Rapid determination of desorption efficiency, and analysis of solvent mixtures for occupational exposure studies

Summary An analytical procedure has been developed for simultaneous determination of solvent mixture vapors to enable evaluation of occupational exposure. To determine the desorption efficiency the volatile components of the solvent mixtures were generated from a glass tube filled with glass wool. This device is easy to prepare and use. These vapors were then collected in activated charcoal tubes and analyzed by capillary gas chromatography. The method was tested with a mixture of 22 solvents, including aliphatic and aromatic hydrocarbons, alcohols, ethers, esters, and ketones, all at low concentrations. All the components were detected. When a 99∶1 mixture of carbon disulfide-dimethylformamide was used for desorption the efficiency was>75% for most of the solvents.     

Reverse fragment based drug discovery approach via simple estimation of fragment contributions

1. Download : Download high-res image (110KB)
2. Download : Download full-size image

     

高荧光量子效率的分子分散型聚芴衍生物的放大自发发射特性

通过将掺杂剂单元用化学键接到聚芴的侧链上,实现了掺杂剂单元在高分子主体中的分子水平分散,开发了一种新型的基于掺杂剂/主体材料体系的分子分散型蓝光聚芴衍生物.与纯聚芴相比,这种新的分子分散型蓝光聚芴衍生物具有很高的荧光量子效率.以这种新的分子分散型蓝光聚芴衍生物为增益介质的激光器件,在Nd:YAG 355 nm脉冲激光泵浦下,获得了较好的放大自发发射光谱,阈值达到0.25 m J/(pulse cm2).从光物理的角度对薄膜的光学增益和光学损耗进行了定量运算和分析,经过拟合发现,当泵浦能量为0.06m J/pulse时,该聚芴衍生物增益系数可达23.08 cm-1,损耗系数为6.96 cm-1.优良的放大自发发射特性表明该聚芴衍生物是非常好的有机激光增益介质材料.     

Synthesis and photovoltaic properties of main chain polymeric metal complexes containing 1,10‐phenanthroline metal complexes conjugating alkyl fluorene or alkoxy benzene by C═C bridge for dye‐sensitized solar cells

Four main chain polymeric metal complexes (P1–P4) based on 1,10‐phenanthroline metal complexes via the Heck coupling have been synthesized and characterized by Fourier transform infrared spectroscopy, ¹H NMR, UV–Vis absorption, photoluminescence spectroscopy, gel permeation chromatography, thermogravimetric analysis, differential scanning calorimetry, elemental analysis, and cyclic voltammetry. To investigate their photovoltaic properties, the dye‐sensitized solar cells based on these polymers dyes are studied, under the illumination of AM 1.5G, 100 mW/cm². The study results show the four polymers exhibit good thermally stable and the solar cells based on them have good device performance, and the maximum power conversion efficiency is up to 0.735% for the solar cells based on P3 with a short‐circuit current (J_sc) of 1.68 mA/cm² and an open‐circuit voltage (V_oc) of 0.62 V. Copyright © 2012 John Wiley & Sons, Ltd.     

Compare study between smoothing efficiencies of epicyclic motion and orbital motion

The smoothing efficiencies of epicyclic motion and orbital motion in CCOS (computer controlled optical surfacing) were compared. CCOS polishing can smooth out mid-to-high spatial frequency errors which are smaller than tool size on optical mirrors due to the rigidity of polishing tools. The smoothing efficiencies of epicyclic motion and orbital motion with pitch lap and RC lap were compared and the result proved pitch lap with epicyclic motion smoothed ∼1.6 times faster than pitch lap with orbital motion while RC lap with epicyclic motion smoothed ∼1.85 times faster than RC lap with orbital motion.     

KClO_4/Zr在石英管内的燃烧发射光谱与燃烧产物分析

为了研究燃烧条件对KClO_4/Zr烟火剂燃烧过程中光辐射性能的影响,考察了KClO_4/Zr在开放环境和不同规格封闭石英管内的燃烧发射光谱和燃烧产物。借助光纤光谱仪、光电二极管和示波器测试了烟火剂燃烧过程中的光辐射能量分布和闪光时间-强度曲线,分析了所得发射光谱在(590±10),(750±10)和(808±10)nm三个主吸收波段内的光谱效率,借助SEM表征了不同燃烧条件下KClO_4/Zr燃烧产物的形貌。结果表明:在开放条件下燃烧时,KClO_4/Zr的燃烧发射光谱在可见光到近红外的宽波段内,最强辐射出现在730~820nm波段。在石英管内封闭燃烧时,随着石英管体积的减少,在石英管外检测到的燃烧发射光谱强度逐渐减弱,光谱能量分布也呈现不同的变化规律,而且对火焰发射光谱分布进行处理后,随着石英管体积的变化,得到(590±10),(750±10)和(808±10)nm波段的光谱效率也呈现不同的变化规律。但是,随着石英管体积的减少,KClO_4/Zr烟火剂的爆燃闪光辐射时间逐渐缩短,峰值辐射强度逐渐提高。增加石英管的直径,有利于在管外获得更高的有效光辐射能量,减少石英管的直径,则有利于提高烟火剂的峰值辐射强度。随着管直径的增大,KClO_4燃烧更加充分,产物粒径较小,呈规则的球状。而管长度的改变对反应并无太大影响。     

Is the US stock market becoming weakly efficient over time? Evidence from 80-year-long data

We propose a degree of market efficiency in terms of entropy concepts. The relative efficiency for the US stock market varies over time from 1929 to 2012, with a slight decline in the past 10 years.     

Dispersion and deposition mechanisms of particles suspended in a turbulent plane Couette flow

Inertial particle transfer in a turbulent plane Couette flow (C flow) was studied using Direct Numerical Simulation (DNS) of the flow combined with a Lagrangian particle tracking approach for particles with Stokes numbers (St) 5, 25 and 125. The particle concentration was assumed low enough, so that the simulations were done under one-way coupling condition.     

Improved efficiency of organic solar cells with modified hole‐extraction layers

The aim of this work has been to study the influence of modified hole‐extraction layers on the performance of organic solar cells (OSCs) based on blends of poly (3‐hexylthiophene) and [6,6]‐phenyl‐C₆₁‐butyric acid methyl ester. The hole‐extraction layers consist of poly (3,4‐ethylene dioxythiophene):polystyrene sulfonic acid (PEDOT:PSS) doped with different concentrations of bromine. Compared with pristine OSC without adding bromine to the hole‐extraction layer, the bromine‐doped OSCs show a 49% increase in the power conversion efficiency (from 2.12 to 3.16%), which could be attributed to the increase of electrical and optical properties of PEDOT:PSS films after the addition of bromine. © 2011 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 50: 125–128, 2012